turning canned cycle on creo 3.0???
why ptc silent on the turning canned cycle on creo 3.0??? why there is no builtin turning canned cycle in creo????? regards asif
View Article3D MOLD Design using Pro Engineer
dear All,please advise and share... is there any one here using Pro Engineer for 3D Mold Design, i mean full complete mold design such as :1. Spliting core-cavity-slide2. Mold Base and standard/custom...
View ArticleMachining time
Hello all,how do youdo for havea machiningtime who is close to the reality?thanks for your help or remark,Thomas
View ArticleProfile milling, avoiding retract
I've been fighting Creo2 (and WF4 previously), trying to avoid or suppress retracting while in a profile milling sequence. I have the retract plane defined 50mm above the fixture and part, but I have a...
View ArticleExporting individual sheetmetal part DXF data from assembly
Hi all, I am trying to export flat sheetmetal DXF data from Creo Parametric 2. The assembly containsa fairly large amount of components that need to be sent to LASER cutting. The arrangement and number...
View ArticleChange lead-in radius in Rough milling
Folks, I'd like to change the lead-in radius when rough-milling. The cutter chatters because the radius is too small so I'd like to increase it. I've looked all over the place and cannot find any way...
View ArticleDynamic milling like MasterCAM?
Good morning, It was brought to my attention by a new coworker that use toprogram using MasterCAM on how to improve our machining process. He showedme some videos of the Dynamic milling...
View ArticleCreo 3.0 & 2.0 Student Editions not opening new manufacturing window and not...
As the title states. I am able to create .prt files with ease and usually the next step after the final save would be to open a new manufacturing window. The recurring problem is that a new window will...
View Articlehow to add part's relation with manufacturing relation
i had made the relation in expert machinist in proe and in part module like 1.total material cost and 2.total process cost (milling) so how do i add this two relation and make it to add and display it...
View Articlehow to use manufacturing parameter into design table
my main objective is to show the machining cost into design templateIn manufacturing module i made 9 different assembly, i make the relation to find out the machining time and setup the perameter =...
View ArticleCreo 3.0 custom trajectory
We recently updated from Creo 2.0 to 3.0 F000. Now I cannot locate the custom trajectory toolpath. I can fake it using a regular 3-axis trajectory, but custom trajectory did a better job of integrating...
View ArticleHaas VF1 Post Processor with Tool Description
Does anyone have a post processor for a Haas VF1, I would like for it to have tool description added aat the beginning. All that I have seen do not have this. I am running WF4(901) 210-6653 Steve
View ArticleClik here to view.
Minimal acceptable tool length
Hi, While looking at SPR resolved between Creo 3 M040 et M050, I noticed a document referring to minimal acceptable tool length....
View Articleptc creo 3 - ramp angle
dear friends;we are using creo 3 for cam programming , in roughing program although I mentioned ramp angle as 5 degree /less than 90 , cutter directly plunging on the material with out taking any ramp,...
View ArticleCreo Machining Tutorial
Hi, I just learned about the creo machining feature and I am curious how to use it. If I have just a regular .prt file where do I start? The NC manufacturing seems to demand a .asm file and not a .prt...
View Articleany one knows about how to get cost of machining for each operation and time...
how to get lets say time for each operation so you use realtion to get time_for_operation*cost_per_min or something like that.
View Article5AXIS HEIDENHAIN POST PROCESSOR
Dear Friends,I introduce my self gopinath as CAM Engineer working in Al Fanar Moulds,Saudi Arabia.If anybody having 5axis post processor for Heidenhain could you for sendit to me.We have one 5 axis...
View ArticlePlay Path Shaded Tool option
The toggle checkbox for Shaded Tool during play path only blanks tool when selected (checked). Unchecked tool displays wireframe. Model display style environment is set to Shading. Is this a known...
View ArticleTraining in MFG
Hi, I'm looking for a trainer who is knowledgeable in 5 Axis mill-turning area in Creo 3.0 Any recommendation ?
View ArticleSolid tool setup - Pro/Manufacturing
I use solid tools to simulate G code in a full blown seat of Vericut. I have a solid tool in Creo that is giving me a problem. The tool design is a 3/8 bull nose end mill with a .06 radius. When I...
View Article