Creo 3.0 & 2.0 Student Editions not opening new manufacturing window and not...
As the title states. I am able to create .prt files with ease and usually the next step after the final save would be to open a new manufacturing window. The recurring problem is that a new window will...
View Articlefeeds and speeds
can anyone give insight on how to have creo automatically output feeds and speeds based on material.
View Article"No relations" message when outputting operations
Not a problem, really, I'm just curious. Whenever I output an operation to a ".ncl" file, the message window pops up a statement: "No relations have been defined for this model." I don't know why this...
View ArticleModuleWorks to replace Vericut
Hi all, just read this in article CS226148,ModuleWorks will replace NCCHECK & VERICUT starting from versions below: Creo Parametric 2.0 M210Creo Parametric 3.0 M090Starting from above versions,...
View Articleverification software
What verification software are you guys using? With PTC moving away from Vericut we may consider other options, posted gcode simulation is a requirement, and ease of use with creo of course. Thanks Josh
View ArticleG-Post FIL Help
After many years of dealing with minor edits to my G-Code, I am trying to put some final touches on my Posts. Does anyone have any ideas on how to get the posts to for out both the X and Y moves after...
View ArticleWhere is Custom Trajectory in Creo 3.0?
In previous Creo versions there was a cutom trajectory button that is no longer visible in Creo 3.0. We use custom trajectory with curves to drive toolpath and take multiple depths of cuts.
View ArticleEliminating X,Y in G02/G03
We recently purchased a Haas VF-2 that will not run on the same post as our older Haas machines. It does not like redundant moves or having a X or Y move within a G02/G03 line that also has an I,J...
View ArticleFree_Feed and Direct move
I have been using the constant_load tool path and now that the retract can be controlled I like it a lot. Except, when I change free_feed from rapid to some value to avoid the collisions Vericut is...
View ArticlePTC Creo Lathe turning with diameter g-code output
Hi Folks, I am have an inconvenient issue using Creo Manufacturing to output lathe code to use on our Haas Lathe. Typically we keep our Haas TL1 lathe in diameter programming mode - this is the easiest...
View ArticleNew Installation CREO Parametric 2.0 (M230) Where is Vericut?
Hello everybody,I have a new PC including Creo Parametric 2.0 (M230) get. Now I vemisse in the PRO-NC the Vericut simulation, it can be that this is no longer present in the package? Greeting Peter
View ArticleModuleWorks not displaying workpiece
So I loaded up M100 this morning to test out the new ModuleWorks and nothing shows up for simulation. I can show everything by checking the box for Target under view, but that doesn't help me with...
View ArticleClik here to view.
Trajectory Milling
Had some free time to work on this today. Source link I created a curve by equation and used that to drive a trajectory milling sequence for some long slots I needed to mill. here is the equation I...
View ArticleMold Cavity_Silhouette Curve_Skirt Surface_Rc Propeller
Hello !! I'm trying to make a mold for my propeller but i have some problems to close the silhouette curve around the hub. I've done some research correct me of i'm wrong and find that the curve is...
View ArticleModuleWorks to replace Vericut
Hi all, just read this in article CS226148,ModuleWorks will replace NCCHECK & VERICUT starting from versions below: Creo Parametric 2.0 M210Creo Parametric 3.0 M090Starting from above versions,...
View ArticleHelp with expert machinist G-code Output
I'm new to pro/E and Creo. I am having trouble with the expert machinist output to G-Code. My Machine tool does not like the format of the post processor. I have the basic 2 ½ D CAM that comes with...
View ArticleG-Post FIL Help
After many years of dealing with minor edits to my G-Code, I am trying to put some final touches on my Posts. Does anyone have any ideas on how to get the posts to for out both the X and Y moves after...
View ArticleDoes Production Machining give .tap and g-code functionality?
Will the production machining option in Creo give me the ability to post process my models in manufacturing mode to a .tap file. Will it also post process to g-code and does it come with the basic...
View ArticlePost Processor for a MultiCAM router
Like most of the newbies here, I'm looking for a post processor. In thiscase, one for a MultiCAM router. Anybody use Pro Machinist with aMultiCAM router?Thanks in advance,Albert
View ArticleSolid tool setup - Pro/Manufacturing
I use solid tools to simulate G code in a full blown seat of Vericut. I have a solid tool in Creo that is giving me a problem. The tool design is a 3/8 bull nose end mill with a .06 radius. When I...
View Article